• 3D Model

Info

Added: Oct 30, 2017 04:16
Author: aeropic
License: Creative Commons - Attribution - Non-Commercial

Description

Yet another linear bushing ?

Yes but this one is a bit special as, if you follow the process, it will print in "spiral vase" which means:

it will be very accurate !... The Spiral Vase setting of Slic3r will raise Z continuously avoiding a layer-change point which would cause a visible seam. The accuracy is given by parametrization of the diameters. It will fit direct from the printer once parametrized to your printer.
A chamfer is included at both extremities on the inner and outer diameters. (no need to trim anything)
it can be made springy
it is self centering
it is very light (around 1g each which means you win 50 g on the Y carriage)
it has low friction and slides on the whole surface of the rods
everything is customizable and MUST be customized (see bellow). As they cost nothing (around 2 cents each) you can play with them, print 4 or 5 prototypes to get the perfect fit
Only drawback, it must be installed inside a standard bushing just because it has to be set inside a cylindrical housing to keep a regular shape.

They are installed on my Y axis and so far they do a great job!

see it here: https://youtu.be/BviIuek-uW4

Print Settings

Printer:
ANET A8

Rafts:
No

Supports:
No

Resolution:
0.2 with a 0.4 nozzle

Infill:
none - spiral vase

Notes:
I printed in PLA. I don't use any lubricant.

This thing must be sliced with Slic3r using the spiral mode. See the 3rd picture. Do not forget to remove the bottom (with 0 layer).

Obviously, you shall print them one by one to get the spiral mode working...
Duration of print is only 5 minutes for one bushing.

Again, please read the next paragraph, the trimming must be done in customizer or (faster) directly with Openscad which is freeware.

Custom Section

let's customize it ...
It is mandatory to trim this model under the customizer or directly with openscad.

You must trim at least the following parameters :

// the outer diameter in mm
outerD=15.0;
Print some samples and adjust outerD first without modifying anything else. Once you get a bearing that fits exactly inside the bushing, you can play with the second parameter (inside diameter)

// inner diameter in mm
innerD=8.0;
The inner diameter can be set here. For a standard LM8UU, just leave this value to 8 mm

// this is used to trim the inner diameter (mm)
filament_margin = 0.92;
The spiral vase prints one perimeter just inside the perimeter of the rod... This "filament margin" is here to offset the inner diameter. On my printer with a noozle of 0.4 mm and a layer of 0.2, the filament width is around 0.45mm which means 0.90 on the diameter.
Basically start with 0.90 and play with this value to get the bushing nearly fully free on the rod (see the video to feel how accurate you have to be...)

You may as well play with the other parameters :

// height in mm
H=23.8; //23.8;
This is the height of the bushing. For a 24 mm, I left 0.2 mm free...

// number of spikes
N = 10;
If you want so, you can play with this to reduce or increase the number of blades or spikes.
10 seems to be the maximal value.

// spike angle
spike_angle = 30;
The blades are not perpendicular to the perimeter they are oriented with an angle. The bigger the angle, the more springy bushing you get. If you do not want any springy effect, set this value to 0.

// twist of blades in deg
blade_twist = 30;
On standard bushing (IGUS like) the spikes are fully radial which means that the friction is applied always on the same part of the rods. To get an even wear of the rods, you can twist the spikes pattern so that along the lenght of the bushing every part of the rods will be in contact of the printed bushing. Set it to 0 if you do not want this !

my other ANET A8 mods
https://www.thingiverse.com/thing:2456797
https://www.thingiverse.com/thing:2430113
https://www.thingiverse.com/thing:2426747
https://www.thingiverse.com/thing:2494319
https://www.thingiverse.com/thing:2498478
https://www.thingiverse.com/thing:2502858
https://www.thingiverse.com/thing:2527328

just for fun ;-)
incredible what i found this morning... I did not know this may exist !!!!!
Thank you to those who watch and like this little springy thing...

Files

File name File size
LICENSE.txt 217.00 B
README.txt 5.76 KB
attribution_card.html 2.18 KB
files/spiral_vase-linear_bearing.stl 6.07 MB
files/spiral_vase-linear_bearing.scad 1.34 KB
images/4125ad986a262a23ccb0145950edfd5f_preview_featured.jpg 35.40 KB
images/9f78201d590b6b0784fcc77caa04cceb_preview_featured.jpg 130.17 KB
images/eb56d2d3dc76248c5d5f902a1a5a8435_preview_featured.JPG 60.84 KB
images/b1ebfd09e4a7358df59bc638d469cf23_preview_featured.jpg 31.59 KB

Leave a Reply